Prevents moisture and vapor migration	Penetrates concrete up to 7 inches		Prevents alkali/efflorescence attack
Prevents metal corrosion and deterioration-Click here for photos	Prevents efflorescence		Increases insulation R factor
Improves weathering resistance	Prevents chloride intrusion		Prevents mildew and fungi
Negative and positive side application	Prevents flaking of paints		Resists acid attack (see table below) *
Adds density and bonding strength	Acid Type	Concentration	Exposure 1	Exposures 2-6
Resists freeze thaw (exceeds 360 cycles) to 2.8% loss by weight	Hydrochloric	37%	Surface etched	No reaction
Hydrostatic pressure to 100 psi (231 ft. below grade)	Nitric	70%	Surface etched	No reaction
Preserves and prepares masonry for paints, coatings, and adhesives	Sulfuric	98%	Surface etched	No reaction
Cures concrete uniformly and increases surface hardness up to 23 %	Phosphoric	85%	No reaction	No reaction

MOXIE 1500 CONCRETE SEALER is water based, non-toxic, and composed of in-organic, chemically reactive, complex compounds which allows full penetration up to seven inches. MOXIE 1500 CONCRETE SEALER undergoes a chemical reaction with the by products of the curing process to form the highest density of cementitious materials, dramatically enhancing all of the natural characteristics of concrete and reducing the capillary voids to practically zero.

MOXIE 1500 CONCRETE SEALER is available in the following packages:

55 gallon drum (US.)

5 gallon pails (US.)

1 gallon bottles (US.)

Applicable Standards:

MOXIE 1500 CONCRETE SEALER meets or exceeds the following performance specifications:

ASTM C 67, Sect. 25 and 29	ASTM C 156	USDA approved	UDOT
ASTM C-309 Performance Specifications *	ASTM C 666	EPA approved	VOC=0

Some steel troweled surfaces which have aged longer than 28 days may need to be shot blasted first, contact manufacturer. Any free or loose dirt, grease, oil, efflorescence or foreign matter must be physically removed first.

MOXIE 1500 CONCRETE SEALER is formulated solely for concrete and masonry products and should not be used on asphalt, metal, or wood products. Will not penetrate acrylic or non-porous rubber base paint. Should not be applied below 40^oF. MOXIE 1500 CONCRETE SEALER will seal against a hydrostatic pressure; however, flowing water must be stopped before application. Very damp, cold days may extend drying times. Higher temperature will shorten drying times.

Mist lightly with water prior to application. If acid washing make sure acid is COMPLETELY REMOVED AND NEUTRALIZED prior to application. Unless used as a curing agent it is recommended to wait no longer than 28 days before application. Surface will still be porous enough to insure proper absorption. Earlier application times are not deleterious and will result in higher compressive strengths. A clean surface is required. Remove any wax, grease, rubber, acrylic based paint, or any other type of surface sealer. Sand blasting, scarifying or bead/shotblasting may be required to allow MOXIE 1500 CONCRETE SEALER to penetrate into the matrix of the concrete. Two coats are required above grade; three coats below grade. Application method depends on time and labor constraints, however, method "One" is preferred.

1) Application Method One: Apply two coats of MOXIE 1500 CONCRETE SEALER 24 hours apart. Apply first coat by saturating the surface. Broom out any puddling. On vertical surfaces allow approximately 12" rundown. When this is nearly dry, MIST WITH WATER to promote deeper penetration. After 24 hours, flood with water, allow to dry approx. 3 hours. REPEAT PROCESS FOR SECOND APPLICATION. If efflorescence (white crystalline salts) appear continued flooding is necessary every 24 hours until efflorescence no longer appears. Typically two to seven days. .

2) Application Method Two: Apply first coat by saturating the surface. Broom out any puddling. On vertical surfaces allow approximately 12" rundown. When this is nearly dry, apply second coat. Allow this to dry but not over 3 hours, then "mist" with water. After 24 hours, flood surface as in APPLICATION METHOD ONE.

NOTE: High porosity, suspended lightweight structural, or below-grade applications may require a third coat. Apply third coat 48 hours after the second coat IN EITHER APPLICATION.

The best concrete cure can be obtained with one heavy application (approx. 250 to 300 sq. ft. per gallon) after initial set, prior to final finish. To moisture/vapor or alkali/efflorescence-proof, proceed with APPLICATION METHOD TWO.

Two coat coverage will yield approximately 150 sq. ft. per gallon, two coats. First coat will use about twice the amount of the second coat. A third or fourth coat is usually required for stucco, gunite, shotcrete or mortar.

1. Due to pH level do not allow this product to come in contact with plant life or leather. Do not allow product to come in contact with glass, porcelain or ceramic tile, aluminum, zinc or galvanized steel. Product will permanently etch or erode the smooth surface. Must be rinsed with water or removed with damp cloth immediately. DO NOT APPLY IN WINDY CONDITIONS.

2. Alkali salts (efflorescence) will react with the carbon dioxide within 24 hrs. - 48 hrs. and become permanent calcium carbonates unless flooding is performed every 24 hrs. until no more efflorescence is present. If not, these salts will require physical removal such as wire brushing or sandblasting.