MOXIE 2000 SUPER PATCH is a high strength, cementitious
mortar for patching or resurfacing concrete, masonry, wood, or asphalt surfaces above and
below grade. Suitable for floors or walls, stucco, gunite and shotcrete repairs. MOXIE
2000 is not suitable for overhead repairs.
Advantages:
Waterproof
Horizontal and vertical surface applications
Skid proof
Greater impact resistance than standard concrete
Feather edge to ¾"
Freeze thaw durability better than standard concrete
Will not peel, crumble, dust, or crack
May be applied over existing concrete floor or wall
Can be used for cove base
200% tensile and flexural strengths over standard concrete
Fireproof
Ideal for stucco, gunite and shotcrete repairs
Description:
MOXIE 2000 SUPER PATCH is a two part, polymer modified,
cementitious patching and surfacing compound. Composed of a laboratory controlled blend of
special portland cement, fine aggregates, liquid bonding agent and specifically formulated
admixture. Exhibits excellent workability and aesthetics. Non-flammable, high strength
mortar with outstanding strength and handling abilities.
Packaging:
MOXIE 2000 SUPER PATCH is available in the following
packages:
70 lb units
20 lb units
10 lb units
Limitations:
Troweling is slightly more difficult than standard
concrete. Certain solvent containing coatings should be avoided (contact MOXIE
International). Do not store the binder under freezing conditions; it must be discarded if
frozen, 320F or below. Do not over-trowel.
Preparation:
Surface: Surface to be patched must be free of all loose,
foreign materials especially oil and grease. (MOXIE 3000 SUPER SOAP or MOXIE 5500 SUPER
CLEANER to clean surface, MOXIE 1600 CLEANER SEALER to seal).
Patching mortar: Mix thoroughly 9 parts of dry material (by
volume) with 1 part water. Then add 1 part of the white liquid binder
(for example, 9
ounces dry mix, 1 ounce water; then 1 ounce binder). Mix thoroughly to get a patching
mortar of proper consistency for troweling (it will be on the dry side).
Water vapor proof patching mortar/slurry: To produce a
water and vapor proof, below-grade, patch or slurry mix for retaining walls, CMU and
porous block mix 1 oz MOXIE 1800 SUPER-ADMIX per 10 lb unit in addition to the above
mixing instructions. MOXIE 2000 SUPER PATCH with the addition of MOXIE 1800 SUPER-ADMIX
cannot be removed from brick or CMU once cured. This mortar residue must be removed as it
is being applied. This is particularly critical with the application of MOXIE 1300 Brick
Sealer. If this mortar residue is not removed it will produce efflorescence.
Surface primer: To make the surface primer use a small
amount of binder, diluted with an equal quantity of water (50% water, 50% binder) for
priming the surface as described under application.
Application:
1. Dampen surface with water, mist, spray bottle or mist
with Hudson sprayer.
2. Using a paint brush, apply the surface primer (diluted
binder) to prime the surface.
3. Take a small amount of patching mortar and brush into
the primed area, working it into any cracks, pits, or crevices.
4. Apply the remainder of patching mortar to pre-treated
area.
5. Trowel like regular concrete until desired finish. Keep
troweling to a minimum. If surface appears hard, sprinkle with
water and complete your finish.
Note: Keep tools clean with water. MOXIE 2000 SUPER PATCH
will PERMANENTLY bond to tools.
One 70 lb. "unit" will cover the following
surface areas to the thickness shown:
Area sq. ft
Thickness Inches
Area sq. ft
Thickness Inches
7 Square Feet @
1.0
28 Square Feet @
1/4
14 Square Feet @
1/2
56 Square Feet @
1/8
Lineal Coverage: Slurry coat:
One 70 lb. "unit" will fill the following
: One 70 lb. "unit" will COAT the following :
Lineal Feet
Dimension
Square Feet
Thickness, Inches
280
3/4" x 1/2"
224
1/32"
NOTE: Application of our Moxie 1500 concrete sealer or
our Moxie MFSII concrete floor sealer can be made 24 hours after patch has
been applied. Because conditions and situations vary, a longer time
is recommended when possible.